Looking to install a shower caddy in your home? You’ve stumbled upon the right place. Zenna Home tension pole shower caddies are designed with your modern home and bathroom in mind. They not only look great but can hold shampoo, razor, soap bars and much, much more. Rest assured if you follow the instructions on this blog post that you can assemble a tension pole shower caddy – with little effort and in no time!
Zenna Home Tension Pole Shower Caddy is a functional & functional item. It will provide the much needed support for your shower items. If you are in need of this type of caddy, then go through the article to understand how to set it up easily and safely.
Table of Contents
Align the caddy with the pole.
Hold the caddy up to the pole. Make sure that you have it aligned so that the pole fits snugly inside the caddy’s cup.
Tighten the bolt on the bottom of the caddy cup by turning it clockwise. Do this until you can no longer turn it, but be careful not to break it.
Make sure that the caddy is secure on the pole and will not fall down. Then, add your shower accessories to the caddy.
To keep your tension rod caddy looking new, clean it with a non-abrasive cleaner once a week to remove soap scum and mildew buildup.
Make sure the caddy is aligned with all of the marks on the pole and starting at the designated level (in our case, 4 feet)
First, measure the height of your shower head on the wall. The bottom of the caddy should be installed at least 4 feet from the floor.
Using a level or a tape measure, mark off where you’ll want the bottom of the caddy to be secured. Once you’ve marked off this initial spot, use a pencil to mark off every 4 inches, up to the top of your shower head.
Next, screw in the two tension screws on either side of pole. If you don’t want to drill into your tile or wall, you can use adhesive wall pads instead.
Slowly extend the pole toward the ceiling until it is flush against your shower head and all four rubber pads are touching tile or wall surface.
Secure the caddy to the pole
Secure the caddy to the pole.
Most tension poles have a thumb-screw cap at the bottom of the pole. Use it to secure the caddy to the pole.
If your caddy does not have a thumb screw, then you will need to wrap wire around the pole and caddy. Cut a piece of 20 gauge wire about 1 foot long (30 cm). Attach one end of the wire to the bottom of the pole and then wrap it around both the pole and caddy (or use two wires, one going around each leg). Twist and squeeze the ends together so that they stay attached. This is a temporary solution until you get a grip cap or shower curtain tension rod.
Double-check that it’s straight.
Installing the Zenna Home Tension Pole Shower Caddy is a quick and easy way to organize your shower. This product adjusts to fit ceilings between 80 and 105 inches tall.
- Measure from floor to ceiling to determine how high you will need to adjust the tension pole.
- Adjust the tension pole according to instructions.
- Make sure the pole is completely straight before tightening it.
- Unscrew the top of the tension pole and adjust so that it is level with the height marks on the side of the pole.
Attach bottom spring.
Place the bottom of the caddy onto the floor of your shower. It should slide under the lip of the unit. Attach the bottom spring to the bottom of pole and tighten it into place with a screwdriver
Attach top spring. Slide the top spring over top of pole and tighten it into place with a screwdriver.
Line up caddy. Line up the holes in the sides of your caddy with the holes on your tension pole. Insert screws through these holes and tighten them in place using screwdriver.
Open shelves
Shelves should be able to open by hand. If they do not, check that all springs are tightened properly and shelves are lined up correctly.
Add your products.
1. Place the expanding end of the shower pole into the base. Rotate the pole until it locks into place.
2. Place the adjustable feet on a flat surface inside the tub or shower. Rotate the feet until they lock into place. Note: If your ceiling height is less than 8-foot-6 inches, adjust the height of the pole by twisting off the upper section of the pole and cutting it to size with a hacksaw. Remove any sharp edges with a file or sandpaper before reassembling.
3. Carefully spread out each section of pole to its full length and place them inside your tub or shower stall at an angle so that they rest against opposite walls.
4. Use your foot to press down on the bottom end cap while pulling down on both poles so that they are parallel to one another and taut against both walls. You may have to rotate one of the
Conclusion
This blog post has everything you need to know about how to install a tension pole shower caddy. It’s pretty easy to get this sort of installation dialed in, especially with the helpful tips and suggestions we’ve provided. If you take your time following these instructions, getting your own tension pole caddy installed shouldn’t be a problem. Give it a shot!