Light fixtures indeed soften and diffuse the light emitted by bulbs, making the space more comfortable to work in. However, they also serve as a breeding ground for all manner of unwanted pests and debris.
While consuming the same amount of energy, dirty lighting fixtures can reduce the amount of light that enters a space while reducing light bulb life expectancy.
Table of Contents
Cleaning Light Fixtures Can Be Dangerous
Cleansing light fixtures can be difficult because ladders are required regularly. When you’re on a ladder, you’re more than likely to unscrew the light fixture, which increases the risk of an accident. At least twice a year, you should remove your light fixtures and give them a thorough cleaning, even if you can clean them while they’re in place.
Light bulbs can also be hazardous because of their heat when turned on. Before beginning to clean fixtures, turn off the light for at least an hour to limit the chance of burning yourself. Electricity is also a potential danger.
Disconnect the electrical components of light fixtures so that you may wash and clean them. You should use a dry dusting tool if you tend it in place. If water or cleaning solvent gets into the electrical components, your lights might be damaged or electrocuted.
How To Clean Kitchen Light Fixtures?
· Routine scrubbing
Weekly, give all of your light fixtures a good dusting. With the light fixtures still in situ, this may be done. Reach and dust ceiling fixtures, chandeliers, and even recessed lights with a long-handled dusting tool. When done regularly, the extensive cleaning of light fixtures should only be required twice a year.
· Decorative Glass Ceiling Lights
Light fixtures can be unscrewed from the ceiling, lamp, or base by loosening the screws. First, remove the light fixture’s dust, bugs, and other debris and dispose of it in the garbage. Next, use a microfiber cloth or equivalent duster to clean both the inside and outside the vehicle. This is all that is required at times.
However, the fixtures will need to be cleaned twice a year. Cleaning glass light fixtures usually take a warm water sink and a few drops of basic dishwashing detergent. Afterward, wipe them off and rinse them with soap and water.
Using a dry towel, make sure they’re scorched, paying particular attention to the interior. Finally, they may be replaced. Glass light fittings should never be put in the dishwasher. You may shatter them if you do so. Spot cleaning glass light fixtures are also possible using glass cleaner.
· Chandeliers
While you may be able to dust your chandelier while it’s in place for routine maintenance, a full-scale cleaning would likely need to take it down at least twice a year. To make reassembly more accessible, you can picture how the chandelier is assembled.
You may make your spray cleaner at home. Use 1/4 cup vinegar and 3–4 cups of water as a starting point for your solution. One segment of the chandelier’s crystals and other parts should be sprayed at a time. Try putting the chandelier back together and see how it looks.
· Illumination in the Ceiling
After the light has been off for at least an hour, frequent dusting within the opening is the best method for cleaning recessed lighting. For more thorough cleaning, remove the bulb and wipe the inside of the recessed region with a moist cloth.
To be extra safe while working, you should switch off the electricity to that area of the house completely. Replace the bulb with a clean one. When you turn on the electricity, the light will be cleaner.
Kitchen Light Fixtures: How Do You Clean Them?
Pendant Lights and Chandeliers
For this reason, you should only do this once or twice a year, as cleaning a chandelier will take a lot of time. Chandelier cleaning can be delegated to your local Merry Maids if you don’t have the time to handle it yourself. Merry Maids employs a unique crystal-cleaning technique that is sprayed on and permitted to dry before being vacuumed. If you’d want to give these goods a whirl, they can be purchased online.
There are two ways to clean these light fixtures of severe DIYers with the crystals on or off. Your preference for reassembling or standing on a ladder for an extended period will dictate how long it takes.
The crystals-off approach, which lets you spend more time sitting down instead of balancing, is described in detail below. It’s also similar to how you’d clean glass globes or bell-shaped pendant light fixtures from a ceiling fan.
It’s essential to remember that cleaning any light fixture requires two people.
You’ll need to:
- Gloves
- A spray canister
- A variety of microfibre cloths
- Vinegar that has been distilled
- Water
- A stepping stool or a ladder
- A sleeping bag
- A bathrobe or bathrobes.
- A cleaning partner
Before you begin cleaning your chandelier, make sure to snap many photos from various vantage points. Use them as a reference when you need to change the crystals. If you have pendant lighting with different globe sizes, you may want to capture a few photos of each.
- Wait until all the bulbs have cooled before turning off the light fixture.
- Place a folded blanket under your chandelier or pendant light to protect the floor underneath. If any parts fall, this will offer a buffer. The chandelier crystals, globes, and other gear will need a place to rest once you remove the towel from the surface.
- Ask a cleaning companion to help you quickly stabilize the ladder to reach the light source. Please don’t place your ladder on the blanket; this might cause it to sway.
- Remove the chandelier’s crystals with care. Please start at the top and work your way to the bottom to keep things organized and pass them down to your cleaning partner. There are a few things you’ll need to keep an eye out for a while installing pendant lighting: screws and other hardware.
- Use a dry microfiber towel to wipe away any dust from your crystals or globe. When dealing with chandelier crystals, you must follow the sequence you laid out your pieces on the blanket. Make reassembly as simple as possible by doing everything you can.
- Fill a spray bottle halfway with vinegar and the rest with water.
- Put on your gloves and spray a microfiber cloth with the solution you’ve prepared. Wipe your crystals or globe using this. Smudges are minimized thanks to the gloves.
- Afterward, use a dry microfiber towel to wipe any residual solution and remove any stains. Before reinstalling your globe, crystals, and other gear, be sure everything is dehydrated.
- Use a dry microfiber cloth or duster to clear dust from the metal component of the fixture before putting the globe or crystals back in their position. You may use a microfiber cloth gently moistened with a mixture of water and a few drops of dishwashing liquid to remove stubborn stains.
- Restores electricity to the light fixture and crystal or globes, if applicable.
